60/72 SERIES MOUNT

The 6072 Series Mount is designed and engineered for the larger 60 and 72 cells that are less than 79.5” x 39.5”. All mounts are manufactured using pre-galvanized steel and heavy-duty corrosion resistance 5000 series aluminum.

Features

• SKUs available for 1, 2, 3, 4 & 6 modules, sinlge SKU mounts either 60 or 72 cell modules for the same price
• No complex sizing documents or need to send spec sheets
• Designed for 100 mph wind speeds, additional bracing is available for higher wind speeds
• Easily installed and adjusted by a single person
• No complex winches or guy-wires
• Pre-galvanized, no upcharges for environmental challenged areas
• Stainless Steel Hardware
• IN STOCK for immediate ground shipment

NOT FOR USE WITH TYPICAL 60 AND 72 CELL MODULES

Top of Pole Mounts are a heavy duty mounting system ideal for single pole, multi panel arrays. Originally designed for 80W BP modules, these mounts accomodate a wide variety of smaller 12V and 24V modules with ease.

Features

• These mounts fit on a User Supplied 4-inch Schedule 40 pipe
• Single column conguration, module mounting rails must be 1 inch larger than the total width of module to be mounted (See table below for models and rail lengths)
• Maximum total module area is 28 square feet
• Manufactured using powder coated steel and heavy duty corrosion-resistant 5000 series aluminum
• In stock for immediate shipment using ground carriers

Our Single Arm Mount is a simple mounting solution for poles, walls and other at surfaces. This incredibly versatile mount has been used on the sides of shipping containers, buildings, as an awning, or mounted to just about any at surface.

Features

• Uses pole diameters of 2” to 4”, Schedule 40 (not included)
• Accommodates module widths between 5.26 and 25.5 inches
• Manufactured using heavy-duty corrosion-resistant 5000 series aluminum
• Engineered for 90 mph wind speeds
• The single arm mounts can be mounted a maximum of 30’ above grade.
• In stock for immediate shipment using ground carriers

Our Side of Pole Mounts have been an industry standard for over 20 years, with new innovations being added continually to improve the products resiliency.

Choose a mount that matches the center-to-center mounting hole distance of the module to be mounted.
Choose a rail length that is longer than the total width(s) of the module to be mounted.

Features

• Uses pole diameters of 2” to 4”, Schedule 40 (not included)
• UNI-SP/01 AND UNI-SP01A can be configured as a TOP OF POLE mount if the center to center hole spacing matches table below
• Withstands wind speeds of 90 mph, additional high wind bracing available - with order of SP-KNBR-001
• Engineered for 90 mph wind speeds

Quick and Easy Mounting on any type of terrain

The Tamarack Ground Mount System our FM 2.3 or 3.1 rails and UL 2703 module mounting components. If 3.1 rails are used, all compo-nents supplied by Tamarack can be shipped economically by UPS. Concrete and 2-inch schedule 40 steel pipe is purchased locally.Modules can be mounted in columns of 3 or 4 modules. As many columns as necessare can be installed.

Features

• Simple Design - Arrays can be in columns of 3 or 4 module high and any width required
• Easy to install - No welding or drilling and two wrench sizes fit all fasteners
• UL 2703 Listed - All components meet the UL 2703 standards for bonding and grounding
• PE Certified - Pre-stamped engineering letters available for most states.
• Easy to Configure - Unlimited system size with tilt angles from 0 to 45 degrees.
• Visually Appealing - Simple to adjust for perfect alignment, even if the surface is irregular
• Easy Wire Management – PV cables and wiring for module-level electronics fits inside rails to avoid time-consuming wire management
• Extremely Robust - For use in locations with wind speeds up to 170 MPH and ground snow loads of up to 70 PSF.

Offering the first major improvement in railed system technology in many years, Tamarack’s rail based FM system is easy to Install, extremely intuitive and can be used with any off-the-shelf roof attachment. Various snow and wind ratings can be met with the two profiles available.
An industry first, our 50/50 Module Clamp works as a mid-clamp and as an end-clamp with all module types. For premium aesthetics, our Channel Clamp can be used at the ends of rows allowing the rails to be cut flush with the edge of the module frames.
The FM System offers multiple innovative assets including: excellent wire management, using the open rail channels for module and MLPE wiring, single tool installation and easy to handle 10.5-foot and 7-foot rails. Shorter rail lengths facilitate easier shipping, transportation, stocking, and handling. Kits made with 7-foot rails can be shipped via UPS!
The rails feature a very unique internal splice design allowing for economical use of shorter rails. The low-cost splice features tool-free installation and does not interfere with module clamps or roof mounts.
Rail mounting is simple and easy. There is never any drilling and parts can be brought on the roof fully assembled and ready to be installed. Simply position the adapter into the T-slots of the rail, and tighten the bolt.

Features

• All bolts tighten with a ½-inch socket
• Wire clips snap into the rail channels to keep module leads in place for the life of the system
• Listed MLPE mounting kits with a UL2703 certification
• A simple ground lug will mount into the top channel, with no drilling required
• Plastic end caps provide the finishing touch to the installation